Sign in to follow this  
Followers 0
mkay

SSD Reallocated sector count raw value

3 posts in this topic

Hey guys,

I am quite new here and wanted to ask for some advise. I have recently experienced a lot of program crashes and after the usual checks for viruses, memory, etc I ran a hard drive check and these are the results. Is a raw value of over 8000 normal for the reallocate sector count? The hard drive came with my laptop and was in use for less than 6months. I appreciate any help very much.

smartctl 6.0 2012-10-10 r3643 [i686-linux-3.5.6-pmagic] (local build)

Copyright © 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===

Device Model: M4-CT128M4SSD3

Serial Number: 00000000124703595771

LU WWN Device Id: 5 00a075 103595771

Firmware Version: 04MH

User Capacity: 128,035,676,160 bytes [128 GB]

Sector Size: 512 bytes logical/physical

Rotation Rate: Solid State Device

Device is: Not in smartctl database [for details use: -P showall]

ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6

SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is: Sun Jun 23 10:21:45 2013 UTC

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

General SMART Values:

Offline data collection status: (0x80) Offline data collection activity

was never started.

Auto Offline Data Collection: Enabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: ( 595) seconds.

Offline data collection

capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 2) minutes.

Extended self-test routine

recommended polling time: ( 9) minutes.

Conveyance self-test routine

recommended polling time: ( 3) minutes.

SCT capabilities: (0x003d) SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 5

5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 8192

9 Power_On_Hours 0x0032 100 100 001 Old_age Always - 1899

12 Power_Cycle_Count 0x0032 100 100 001 Old_age Always - 132

170 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 4

171 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4

172 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 0

173 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 8

174 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 23

181 Program_Fail_Cnt_Total 0x0022 100 100 001 Old_age Always - 850407981185

183 Runtime_Bad_Block 0x0032 100 100 001 Old_age Always - 0

184 End-to-End_Error 0x0033 100 100 050 Pre-fail Always - 0

187 Reported_Uncorrect 0x0032 100 100 001 Old_age Always - 1060214

188 Command_Timeout 0x0032 100 100 001 Old_age Always - 0

189 Unknown_SSD_Attribute 0x000e 100 100 001 Old_age Always - 81

194 Temperature_Celsius 0x0022 044 035 000 Old_age Always - 56 (Min/Max 23/65)

195 Hardware_ECC_Recovered 0x003a 100 100 001 Old_age Always - 374

196 Reallocated_Event_Count 0x0032 100 100 001 Old_age Always - 4

197 Current_Pending_Sector 0x0032 100 100 001 Old_age Always - 0

198 Offline_Uncorrectable 0x0030 100 100 001 Old_age Offline - 0

199 UDMA_CRC_Error_Count 0x0032 100 100 001 Old_age Always - 0

202 Unknown_SSD_Attribute 0x0018 100 100 001 Old_age Offline - 0

206 Unknown_SSD_Attribute 0x000e 100 100 001 Old_age Always - 4

SMART Error Log Version: 1

Warning: ATA error count 0 inconsistent with error log pointer 1

ATA Error Count: 0

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 0 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -1 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -2 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -3 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -4 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]

60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED

ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

SMART Self-test log structure revision number 1

No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS

1 0 0 Not_testing

2 0 0 Not_testing

3 0 0 Not_testing

4 0 0 Not_testing

5 0 0 Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

Share this post


Link to post
Share on other sites

There appears to be something seriously wrong with that SSD. I'd get important files off and RMA it.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0