Jump to content


Photo

SSD Reallocated sector count raw value


  • You cannot start a new topic
  • Please log in to reply
2 replies to this topic

#1 mkay

mkay

    Member

  • Member
  • 2 posts

Posted 22 June 2013 - 07:48 PM

Hey guys,
I am quite new here and wanted to ask for some advise. I have recently experienced a lot of program crashes and after the usual checks for viruses, memory, etc I ran a hard drive check and these are the results. Is a raw value of over 8000 normal for the reallocate sector count? The hard drive came with my laptop and was in use for less than 6months. I appreciate any help very much.

smartctl 6.0 2012-10-10 r3643 [i686-linux-3.5.6-pmagic] (local build)
Copyright © 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model: M4-CT128M4SSD3
Serial Number: 00000000124703595771
LU WWN Device Id: 5 00a075 103595771
Firmware Version: 04MH
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jun 23 10:21:45 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 595) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 9) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 5
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 8192
9 Power_On_Hours 0x0032 100 100 001 Old_age Always - 1899
12 Power_Cycle_Count 0x0032 100 100 001 Old_age Always - 132
170 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 4
171 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
172 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 0
173 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 8
174 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 23
181 Program_Fail_Cnt_Total 0x0022 100 100 001 Old_age Always - 850407981185
183 Runtime_Bad_Block 0x0032 100 100 001 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 001 Old_age Always - 1060214
188 Command_Timeout 0x0032 100 100 001 Old_age Always - 0
189 Unknown_SSD_Attribute 0x000e 100 100 001 Old_age Always - 81
194 Temperature_Celsius 0x0022 044 035 000 Old_age Always - 56 (Min/Max 23/65)
195 Hardware_ECC_Recovered 0x003a 100 100 001 Old_age Always - 374
196 Reallocated_Event_Count 0x0032 100 100 001 Old_age Always - 4
197 Current_Pending_Sector 0x0032 100 100 001 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 001 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 100 100 001 Old_age Always - 0
202 Unknown_SSD_Attribute 0x0018 100 100 001 Old_age Offline - 0
206 Unknown_SSD_Attribute 0x000e 100 100 001 Old_age Always - 4

SMART Error Log Version: 1
Warning: ATA error count 0 inconsistent with error log pointer 1

ATA Error Count: 0
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 0 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]
ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -1 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]
ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -2 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]
ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -3 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]
ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

Error -4 occurred at disk power-on lifetime: 1899 hours (79 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 80 08 bb ed 40 at LBA = 0x00edbb08 = 15579912

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]
ef 02 00 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Enable write cache]
60 90 80 a0 ba ed 40 00 29d+10:08:12.704 READ FPDMA QUEUED
ef 90 03 00 00 00 00 00 29d+10:08:12.704 SET FEATURES [Reserved for Serial ATA]

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

#2 FastMHz

FastMHz

    Member

  • Member
  • 400 posts

Posted 23 June 2013 - 08:34 AM

There appears to be something seriously wrong with that SSD. I'd get important files off and RMA it.

Production: Vishera 8350/32gb RAM/Dual SSD/VelociRaptor/Radeon 7750
Gaming: Phenom II 955/16gb RAM/SSD/VelociRaptor/Radeon 7950
Retro: K6-2 550/256mb RAM/160gb HDD/CompactFlash/3DFX/ATI AIW Pro/SB16/DB50XG
http://www.fastmhz.com

#3 mkay

mkay

    Member

  • Member
  • 2 posts

Posted 25 June 2013 - 06:46 PM

Thank you very much for your reply!



0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users